The H in HBD64 is not a minor ordering detail. It marks the temperature grade: this variant is specified from minus forty to plus one hundred and twenty-five degrees Celsius, while the FBD version of the same device stops at plus eighty-five. The LPC2194HBD64 is otherwise the 64-pin, 256 KB flash, 16 KB SRAM ARM7TDMI-S part with four CAN channels that made it a favourite for automotive gateways. Reverse engineering a secured LPC2194HBD64 chip starts with that letter, because it changes the thermal history the package has survived.
Four Channels In Sixty-Four Pins
| Part | Flash | CAN channels | Package | Temperature |
|---|---|---|---|---|
| LPC2114FBD64 | 128 KB | 0 | LQFP64 | -40 to +85 C |
| LPC2119FBD64 | 128 KB | 2 | LQFP64 | -40 to +85 C |
| LPC2129FBD64 | 256 KB | 2 | LQFP64 | -40 to +85 C |
| LPC2194HBD64 | 256 KB | 4 | LQFP64 | -40 to +125 C |
Four interconnected CAN controllers with a shared acceptance filter consume a large share of the pin multiplexing on a 64-pin body. There is no external memory controller, so the entire application lives in the 256 KB on-chip array. That is a useful constraint: no parallel bus to listen to, no off-die code store, and no second chip to misidentify as the firmware carrier.
The acceptance filter tables and message objects live in RAM and peripheral registers. A flash read gives the code that configures them, not the running configuration. On a gateway board that distinction is usually the difference between a usable answer and a confusing one.
Four controllers also mean four independent interrupt sources in the vectored interrupt controller, and their vector addresses are a reliable way to identify the CAN handlers in a recovered image. The acceptance filter is shared, so a disassembly that shows one large identifier table rather than four separate ones is behaving exactly as the silicon does; treating it as four independent stacks leads to a wrong map of the code.
Why The Grade Matters Physically
Reverse engineering secured LPC2194HBD64 chip work is mostly about thermal history, not about a stronger lock.
A part rated to 125 C is generally used where ambient temperature is high, which means long thermal cycling, often a different solder profile, and frequently a conformal coating that has to be removed before any package-level work. Decapsulation is a chemical and thermal process; a die and package that have already seen years of elevated temperature can behave differently from a benign-environment sample. We record the marking and date code before choosing a route, and we treat the grade as a real variable rather than a catalogue footnote.
Charge retention on flash is temperature-dependent. A device that has spent its service life hot is more likely to have marginal cells, which is exactly the situation where the on-chip error correction becomes relevant to an extraction.
The Protection Word
Code Read Protection is a 32-bit value at 0x1FC. Writing 0x12345678 gives CRP1: JTAG disabled, ISP read and compare disabled, sector 0 writes blocked, sector erase still available. 0x87654321 gives CRP2, where only a full-chip erase remains. 0x43218765 gives CRP3, which disables ISP entry through P0.14 when valid user code is present. Early bootloader revisions implemented only the middle level; the /00 and /01 silicon added the three-level scheme. A version query over the serial port is the first electrical step.
Before that, the boot ROM checks the vector checksum: the word at 0x14 must make the eight exception vectors sum to zero. If it does not, the part drops into ISP regardless of the intended protection. So the observable state of a CRP3 device depends on the integrity of sector 0, which contains the vectors, the checksum and the CRP word together.
Practical Sequence
We identify the marking, the date code and the bootloader revision, then document the boot behaviour on a bench supply with reset under control. A CRP change only takes effect after a full power cycle, so a recently programmed part may still be open. The array is read in sector blocks with the ECC check bytes retained, and twice from different angles so a marginal cell is not silently corrected into a plausible instruction. The delivered image has 0x14 recomputed and a sector map marking blank regions.
Related Work
The contact page is where markings and board photographs go. The protection walkthrough sets out the layers in order, and this 32-bit ARM case is a comparison on a different architecture. For the two-CAN predecessor see the LPC2119FBD64; for the 144-pin device with the same four channels and the same temperature grade, see the LPC2294HBD144.